GPC® F2

General Purpose Controller, Intel 80C32

GPC® F2 English Tech. Manual PDF format.

Ver. 3.00 - Rel.. 18 January 1999.

The GPC® F2 is a powerfull control module of ABACO® family, capable of operating in stand alone mode or as an intelligent peripheral, and/or remoted, in a wider telecontrol or aquisition network, with an excellent price/performance ratio.
The extreme modularity of this card makes the same the ideal component for the construction of architectures with distributed logic affording good resources both in terms of processing and I/O interconnections. The completeness of GPC® F2 makes it suitable to meet on its own, control requirements of medium complex units or automations. When a more complex system is required, the performances are increased using suitable grifo® cards to be assembled on the powerful industrial ABACO® BUS. Each connector has standard pins out that allows a direct connection with all the I/O BLOCK module or a fast and inexpensive connection with proper field interface manufactured by the user and other companies.
The most interesting characteristic of GPC® F2 is that it can be equipped with a wide range of µP. It is in fact possible to get it by the standard 80C32; by the fast DALLAS 80C320 and many of the compatible models, either with or without internal ROM. The characteristics of the card remain basically the same, but its performance changes according to the built in µP.
At present there are some developping software tools which allow the card to be used as developping system of itself both in asselmber and evoluted languages. Noteworthy among these are the developement tools as the C compilers, the BASCOM 8051 and the handy BASIC F2. With these software tools the user can develop its application programs in a very fast and confortable environment; it is sufficient a serial connection to a common personal computer.

• Single Europe size card 100x160 mm for ABACO® BUS.
• 80Cxxx CPUs with clock from 11 to 22 MHz (80C32, 87C52, 80C320, etc).
• Sockets up to max 96K of memory divided in: 32K RAM,EPROM; 32K RAM,EEPROM; 16+16K programmable EPROMs.
• Programming socket for two EPROMs also with intelligent algorithm.
• 16 digital I/O lines, managed by software.
• 8 ways dip switch readable from software; if necessary it can be changed in others 8 I/O digital lines.
• 3 LEDs for feedback of the different card statuses.
• On board Buzzer for sound, driven by a PWM line available on connector.
• Up to three 16 bit timers counters with related control lines, inside the CPU.
• Six 16 bit timers counters, driven by 82C54, capable of frequency and counting signals management.
• 2 RS 232 serial line, one full duplex and the other half duplex.
• Connector interface for 8 bit BUS ABACO®.
• Standard I/O ABACO® connectors with 20 and 16 pins.
• Real Time Clock calendar that manages date and time by software.
• Back up circuitry for real time clock through on board Lithium battery.
• Single power supply +5 Vdc, 340mA.
• Wide range of developement software such as: Monitor; Debugger; NoICE, GET 51 and BASIC Interpreter; BASIC Compiler, BXC51 and C Compilers; µC/51, CMX, FORTH; PLM 51; etc.

BASCOM-8051

W95/NT 8051-BASIC Compiler

BASCOM-8051© is a Windows BASIC COMPILER for the 8051 family It is designed to run on W95/NT and has all the features of BASCOM LT. In addition it has full support for arrays and the single floating point type.

µ C / 5 1

ANSI C Compiler for 8051

Develop high quality software for any 8051 in ANSI C. µC/51 comes with an incredible optimizing compiler, you can even write software in ANSI C on 8051's with 1kB of code memory! µC/51 is absolutely complete: user friendly multi file Editor, Compiler, Assembler, Downloader, Source
Level Debugger. You will not need anything else.

PASCAL 51

Pascal compiler for 8051

The Pascal 51 is a compiler capable to generate code for the I51 family of microcontrollers, that use almost all the instructions defined in Wirth's Pascal. Thanks to his integarted developmen environment it is really simple to use and offers advantages in hardware resources management, available in the microcontrollers. Moreover objects and precompiled units can be used too.

LadderWORK

The LadderWORK Integrated Development Enviroment (IDE)

The picture below, represents the apperance of the program LadderWORK on your computer. LadderWORK has an integrated enviroment feature, allowing you to draw schematics, compile programs and upload code to PLC always working on the same window. The integrated enviroments are composed by several parts described below. 

Data Sheet GPC® F2, Rel. 99.01

Home Cards Categorical Index CPU