GPC® R168

General Purpose Controller

Relays; 16 Inputs; 8 Outputs, 4 A/D, 1 D/A

GPC® R168 English Tech. Manual PDF format.

Ver.5.00 - Rel. 07 February 2001.

GPC® R168 board is a powerful low cost module, capable to work in autonomy as intelligent peripheral and/or as remote controlled device in a network of telecontrol and/or acquisition. It belongs to M Serie CPU cards, its size is 22.5x82x90 mm.
GPC® R168 board is provided with plastic container for direct mounting on standard Omega rails type DIN 46277-1 and DIN 46277-3. Thanks to the low cost of this CPU serie, it is possible to successfully solve, also all those small automation problems, which have a limited cost budget. Using the wide range of developing softwar tools, available for the GPC® R168 such as BASCOM 8051 or the very comfortable Intel Intel MCS BASIC-52 (download the English manual ) to use in match with BXC51, and so on, it is possible to complete the applications in a very short time and with minimum investments. The card is provided with comfortable connectors that simplify the connection with field signals, requiring no further modules and further cost. Moreover these connectors reduce times when possible up date and assistance phases must be performed.

• Intelligent Abaco® module of the M Serie with 22,5x82x90 mm overall dimension
• Housing for Omega-Rail DIN 46277-1 and DIN 46277-2 types
• Available in 4 different versions with the following CPUs:
  • GPC® R168 with 89C52 22MHz, 32K external RAM.
  • GPC® R168A with Atmel 89S8252 22MHz; 8K internal FLASH; 2K internal EEPROM; 32K external RAM
  • GPC® R168AT with Atmel-Temic 89C51RC2 22MHz; 64K internal FLASH; 1K internal XRAM; 2K internal EEPROM; 32K external RAM; serial ISP Flash programming through RS 232
  • GPC® R168P with Philips P89C51Rx2 or Atmel T89C51Rx2 22MHz; from 16K to 64K internal FLASH; from 512 bytes to 1K internal RAM; 32K external RAM; serial ISP Flash programming through RS 232
• Total memory addressing of 96K, divided in;
  • 32K Static RAM soldered
  • 64K Flash EPROM inside the microcontroller
• Compatible code with the famous 8051 family of µP
• Real Time Clock with 256 Byte of internal RAM
• Back-Up circuitry for RTC and RAM, through LITHIUM battery
• Real Time Clock output for /INT management or frequency output
• 16 NPN idigital input lines, galvanically isolated; 8 of them are connected to the microcontroller and 8 are connected to PCF8575 that generates INT ad whenever inputs change
• External INT line, galvanically coupled
• 8 5A Relays output
• 4 A/D lines, 8 bit through PCF 8591
• 1 D/A line, 8 bit through PCF 8591
• I/O connections through quick release screw terminal connectors
• Three 16 bits Timer-Counter
• Serial line in: RS232, RS422, RS485 or Current Loop.
• Built-in Switching power supply
• Coupled galvanically I/O section powered at 24 Vdc
• Supply of the on board logic: 5Vdc or 10÷40 Vdc or 8÷24Vac
• Supply protection through TranZorb™
• Wide range of developping Software tools such as C Compiler, BASCOM LT , BXC51, Assembler, Monitor, NoICE, HTC-51, FMO52, BASCOM 8051, KSC, UMPS, CMX, LadderWORK, and so on.

EXPS 2 The EXPS 2 module is a complete, low cost, switching power supply with extremely reduced dimension, that can be used in conjunction with grifo® cards as GPC® R94, GPC® T94, GPC® R63, GPC® T63, GPC® R168, GPC® T168, QTP 12/R84, etc.

A C C E S S O R I E S
	CKS AMP 8 Connector KIT Set, 8 pins 8 Female pins + AMP plastic housing for QTP_03, etc..
	AMP8 Cable AMP Cable Connector, 8 pins 1 m cable with 8 pins female AMP connector for QTP_03, etc..

BASCOM-8051

W95/NT 8051-BASIC Compiler

BASCOM-8051© is a Windows BASIC COMPILER for the 8051 family It is designed to run on W95/NT and has all the features of BASCOM LT. In addition it has full support for arrays and the single floating point type.

µ C / 5 1

ANSI C Compiler for 8051

Develop high quality software for any 8051 in ANSI C. µC/51 comes with an incredible optimizing compiler, you can even write software in ANSI C on 8051's with 1kB of code memory! µC/51 is absolutely complete: user friendly multi file Editor, Compiler, Assembler, Downloader, Source
Level Debugger. You will not need anything else.

LadderWORK

The LadderWORK Integrated Development Enviroment (IDE)

The picture below, represents the apperance of the program LadderWORK on your computer. LadderWORK has an integrated enviroment feature, allowing you to draw schematics, compile programs and upload code to PLC always working on the same window. The integrated enviroments are composed by several parts described below. 

Data Sheet GPC® R168 Rel. 00.12

Home Cards Categorical Index CPU Table