GigaLog S datalogger

Product GlogS GigaLog S datalogger, LCD alpha 2x16	Product GsDin GigaLog S datalogger in DIN rail housing	Product GsGraph GigaLog S datalogger with colour LCD in housing	Option for GlogS GsLcd LCD graphic colour 320x240 with touchscreen	Option for GlogS, GsDin, GsGraph Gsm65 Modem GSM/GPRS + antenna

GigaLog S is a data logger for Gbytes of data using microSD memory cards.
With GigaLog S any embedded system can log its data easily, for a very long period, and readable by a PC.

GigaLog S automatically recognizes microSD memory cards, and creates files to store the data into it. When switching power on, or changing the memory card, new data will be appended to the files. Stored data can be read on a PC using a simple microSD adapter. The memory card appears as a removable disk to the PC. All data from the Rs232 is in a single file, analog data in another file on the disk.
You may also upload stored data from the board by USB or Rs232 into a file on the PC.

GigaLog S is available as board or in a housing to be mounted on a DIN rail.
GigaLog S is also available with a graphic LCD to show rescend data.

Storing data from analogue or digital inputs
Gigalog S has 16 single-ended inputs. Couples of inputs can be used as differential inputs. Each input can be configured as analog, digital, or counter. Gigalog samples these inputs regularly and stores them on the disk in a file.
Each input, or pair of inputs can be configured as:

• Unused
• Direct Voltage -0.1 .. 1.2 V
• Direct Voltage -0.1 .. 1.2 V with protection
• Direct Voltage -0.1 .. 1.2 V with Low Pass Filter 1 kHz
• Direct Voltage -0.1 .. 1.2 V with Low Pass Filter 50 Hz
• Voltage -0.5 .. 6.5 V
• Voltage -1 .. 13 V
• Voltage -3.4 .. 41 V
• Voltage -10 .. 123 V
• Voltage -22 .. 270 V
• Voltage -33 .. 405 V
• Voltage -1 .. +1 V
• Voltage -12 .. +18 V
• Voltage -1.2 .. 1.2 V differential
• Voltage -12 .. 12 V differential
• Current 0 .. 25 mA
• Thermocouple type K
• Pt100
• Pt1000
• Digital Input
• Digital Input with pullup
• Digital Input, high voltage
• Counter
• Counter with pullup
• Counter, high voltage
• Counter with S0 output
• Virtual input, calculation
• Virtual input, long time counter
• Virtual input, personal extension

Utility program GigaTerm shows, where to put jumpers and resistor onto the board.

Storing incoming data from Rs232
All data coming in from one of the two serial Rs232 interface can be stored on the disk in a file. A data frame from the Rs232 is any consecutive data until there is a gap of at least 0.5 seconds. GigaLog can be configured to add a time stamp (yyyy:mm:dd hh:mm:ss) in front and/or at the end of a data frame.

More Inputs

You may add more inputs to the GigaLog S data logger using Remote Acquisition modules. These Modules are frequently used in industries, and they come from several suppliers. AdvantechÆ ADAM-4000, AdlinkÆ NµDAM-6000 ICPÆ I-7000, eDAM-8000. Use the RS2 port of the GigaLog S board to create a RS485 network. The GigaLog S is the master of the network. You may connect up to 9 slaves to GigaLog S. Other GigaLog S board can also be connected as slave modules. GigaLog S handles up to 100 inputs, a0 to a15 are on the board, a16 to a99 are remote. You may configure for all inputs the expression to calculate the engineering value from the raw value before storing it to the memory card. All inputs can be displayed on the LCD, and on the optional graphical LCD.

GigaTerm
PC Tool GigaTerm allows you to communicate with the GigaLog board:

• Keep configuration in files
• Configure the board
• Calibrate inputs
• Create macros
• Upload stored data
• Download a new firmware
• Compile your own firmware
• Display all analogue inputs in real time as bargraphs, or as history over 120 seconds

GigaData
PC Tool GigaData displays graphically the recorded data.

Technical data

Analogue inputs	16 single ended, or 8 differential, or mixed
ADC resolution, technology	24 bit delta-sigma
Impedance	>10 M Ohm
Resolution with a perfectly stable input signal at 1ms sampling, typ	16 bits
at 10ms	18 bits
at 100ms	19 bits
Input options	-0.1 - +1.2V -0.1 - +1.2V with low pass filter -0.5 - +6.5V, -1 - +13V, -3 - +41V, -10 - +123V -1 - +1V, -12 - +18V -1 - +1V differential, -12 - +12V differential 0-25mA Thermocouple K, J Pt100, Pt1000 Digital, switch with pullup, high voltage Counter, switch with pullup, high voltage
Additional Inputs	Up to 100 inputs over Rs485 network: Gigalog S, or remote acquisition modules.
Memory card	micro sd-card, 2 G per file (FAT32) Sandisk, any size
Sampling	>= 1ms
Storing Rs232	<= 115200 bd
Programmable	Command macros Programmable in c
LCD	Character 2x16 Or graphic colour tft 5.7" 320x240 + touch panel, backlight (option)
Serial interfaces	2 Rs232 1 Rs485 1 USB
Other outputs	2 solid state relays
Remote Control by GSM/GPRS Transfer of data to Internet Set clock from Internet	with GSM65 (option)
GPS Set clock from GPS	with GSM65b (option)
Power supply	Gigalog S Board: 6 - 15V, 70ma Graphic LCD: 12V, 300mA Gsm65: 6 - 15V, 60mA, 1A (peaks)
Low power mode	< 1mA
Dimensions	GlogS Board: 101x86x15 mm, 75 g GsDin Din housing: 106x91x80 mm, 220 g GsLcd Graphic LCD: 167x108x37 mm, 260 g GsGraph GlogS + GsLcd + housing: 200x122x58 mm, 630 g Gsm65: 48x32x13 mm, 12g
Temperature	Operating: -10 - +50 C Storage: -20 - +70 C

Home Indice Indice Categorico